Results 1 to 6 of 6
-
11-01-2011, 10:09 PM #1
need advice on putting together a new chain
From what I hear I need to press my chain together with out a master link on a XR650R.
Anybody know if this is a must do?
I would really hate to find out the hard way with a cracked case.
-
11-01-2011 10:09 PM # ADS
-
11-02-2011, 09:03 AM #2
Your XR650, like most bigger dual sport bikes, will come with a rivet type master link on a 525 cahin instead of a clip type link typically found on 520 chains. That would be my guess. You can buy 525 clip type master links too, otherwise you'll have to have a special tool to do the rivets on the master link. So yes, you need to rivet your 525 chain master link.
I simply changed my 525 chain to a 520 chain (more common and easier to find sprockets for) with a clip type master. I was also getting new sprockets. I strongly recommend http://www.procycle.us for your needs. They cater to dual sport, big bore bikes.beefcake. BEEFCAKE!
-
11-03-2011, 11:32 PM #3
Hmm I bought a DID 520 VM with steel front and rear sprokets but it is an X -ring gold chain made mostly for ATV's with some of the highest tensile stregnth like 1800 plus pounds. 1827 or 1872 I think, And from what I understand the x ring helps with light dust and mud for keeping chain clean. It does come with a reg. master link. Oh and after a closer looksie it is a Gold and Black chain?
THe Manual says 520 DID 110 o-ring for stock But I heard that they should always be rivet pressed. I have know idea but if I can use the supplied master link this would save me some on the tool thing. But maybe not my case when chain gets thrown.
I did decide to go back to a Dunlop 606 for the rear as it has given me my best tread life so far. Made a big rookie mistake by trying to turn my maxxis desert IT the other way when I got a flat at about 50% and have just about ripped every knob off down the center. Live and learn. Thought I could get better life with a fresh cliff face for digging. Big mistake as now i'm building a slick real fast LOL.
Should be able to completely destroy in the morn and maybe I can save the new tube for the new tire if I can time things well LOL.
-
11-18-2011, 01:08 PM #4
Well the local Honda shop says $127-$170 for this job
Yeh I think I'll invest in the heavy duty tool that should pay for itself first time with a little fudge room on the gravy train.
Hell even the local KTM shop says $100 for same job and we all know they are all about the green backs.
-
11-18-2011, 03:40 PM #5
Or you could buy a clip type masterlink for $6. Just sayn'.......I've run clip links on my Dr650 thru some HARD off road/dune singletrack riding and I use it to commute 2-3 times a week as well. The clips are fine! Save yourself the $100 and buy me something for christmas!
beefcake. BEEFCAKE!
-
11-18-2011, 06:19 PM #6
I decided to go ahead and get the proper tool for the job and not take any chances when it comes to my crankcase. I hope this does not haunt me in the future but the way I see it is that the closer I stay to the specks by the pros the better of I am. MODS/FARKLE are good but some things are best not messed with IMHO
But then again sometimes a fool and his money are soon parted with.
And yes this tool will soon be rentable LOL.
Similar Threads
-
Putting in jointly for a general season permit
By Wasatch Rebel in forum Hunting & ShootingReplies: 8Last Post: 02-06-2009, 10:28 PM -
Putting around in the Jeep near Green River, WY
By greyhair biker in forum Offroad 4x4, Side by Side and ATVReplies: 6Last Post: 10-21-2008, 10:44 AM -
Putting out the feelers
By Gutpiler_Utahn in forum General DiscussionReplies: 5Last Post: 08-13-2008, 08:35 AM -
[Trip Report] Putting around the desert
By accadacca in forum MotorcyclingReplies: 2Last Post: 04-24-2006, 04:24 PM -
Chain Gun
By accadacca in forum General DiscussionReplies: 0Last Post: 07-06-2005, 07:46 PM
Visitors found this page by searching for:
Outdoor Forum