ilanimaka
03-20-2009, 01:22 PM
A while ago, I had to offload some of my shootin irons. Now I have reloading equipment that I don't use and probably won't for the forseeable future. Thought I would offer it up here first. Afro
.223:
- 3 die set by Lee
- Factory crimp die
- All necessary shell-holders for a Lee press & hand primer
- Lee case length guage
- 43 rounds of hanloads (55gr Hornady BT) (Gave me fantastic groups but didn't have enough gas to cycle my AR)
- 50 New brass
- 154 Once fired brass
- 500 CCI Small Rifle 400 primers
- 53 Hornady BT bullets
- 2 - 50rd ammo boxes
- 1 - 100rd ammo box
I figure this stuff is valued at a bit over $100. Make me a reasonable offer and it's yours. This would be a good way to get into reloading if you want to start. I'll even throw in my .223 load data.
.44 Mag/Spec:
- 3 die carbide set by Lyman
- All necessary shell-holders for a Lee press & hand primer
- Lee case length guage
- 18 rounds of 205gr moly-coated RNFP lead rounds (RNFP - Round Nose Flat Point) (These are light target rounds made for plinking.) (I also have another couple hundred of these in Kansas that I'll send out on my dime if somebody buys this set.)
- 1 box (20 rounds) Winchester Black Talon ammo (This stuff generally runs about $2 per round. I bought them for home protection rounds.)
- 53 CCI Large Magnum primers
- 56 240gr Winchester HP bullets
- 200+ 205gr moly-coated RNFP bullets
- Reloading brass holder
- 40 pieces of brass (have been reloaded three times and no signs of wear other than needing some time being cleaned)
- 2 - 50rd plastic ammo boxes. (There are another 4 or 5 of these with the ammo in KS.)
I figure this stuff will go for around $80 but make me an offer. As with the .223 equipment, I'll throw in my load data with this. Hell, I'll even throw in the rest of my H110. There's not much, but you could prolly get another 50-100 loads out of it.
.223:
- 3 die set by Lee
- Factory crimp die
- All necessary shell-holders for a Lee press & hand primer
- Lee case length guage
- 43 rounds of hanloads (55gr Hornady BT) (Gave me fantastic groups but didn't have enough gas to cycle my AR)
- 50 New brass
- 154 Once fired brass
- 500 CCI Small Rifle 400 primers
- 53 Hornady BT bullets
- 2 - 50rd ammo boxes
- 1 - 100rd ammo box
I figure this stuff is valued at a bit over $100. Make me a reasonable offer and it's yours. This would be a good way to get into reloading if you want to start. I'll even throw in my .223 load data.
.44 Mag/Spec:
- 3 die carbide set by Lyman
- All necessary shell-holders for a Lee press & hand primer
- Lee case length guage
- 18 rounds of 205gr moly-coated RNFP lead rounds (RNFP - Round Nose Flat Point) (These are light target rounds made for plinking.) (I also have another couple hundred of these in Kansas that I'll send out on my dime if somebody buys this set.)
- 1 box (20 rounds) Winchester Black Talon ammo (This stuff generally runs about $2 per round. I bought them for home protection rounds.)
- 53 CCI Large Magnum primers
- 56 240gr Winchester HP bullets
- 200+ 205gr moly-coated RNFP bullets
- Reloading brass holder
- 40 pieces of brass (have been reloaded three times and no signs of wear other than needing some time being cleaned)
- 2 - 50rd plastic ammo boxes. (There are another 4 or 5 of these with the ammo in KS.)
I figure this stuff will go for around $80 but make me an offer. As with the .223 equipment, I'll throw in my load data with this. Hell, I'll even throw in the rest of my H110. There's not much, but you could prolly get another 50-100 loads out of it.